500+WHP tC, what it took, lots of *PICS*
#201
Originally Posted by OC3RULZ
Originally Posted by DezodDon
Hmm, interesting.
Your pump gas dyno shows a torque spike at 4600 which generally coincides with peak boost. And your 25 psi race gas dyno shows the same torque spike at 5100 again which would coincide with where your peak boost is made.
Which is pretty much what I was getting at, and why I asked about your AR. On an engine that size you should see peak boost around 4000-4200 especially with a set of cams, ported head and intake manifold.
To be honest with you though, the design of the intake manifold is poor at best and it looks like it was just a rebadged venom/golden eagle unit. I don't know what this makes compared to stock but again based on my experience I would almost think that it kind of hurts the power, or at least compared to a properly designed piece. A box with runners is not conducive to laminar flow.
Either way, the car makes good power and I'm sure it's a blast to drive.
Your pump gas dyno shows a torque spike at 4600 which generally coincides with peak boost. And your 25 psi race gas dyno shows the same torque spike at 5100 again which would coincide with where your peak boost is made.
Which is pretty much what I was getting at, and why I asked about your AR. On an engine that size you should see peak boost around 4000-4200 especially with a set of cams, ported head and intake manifold.
To be honest with you though, the design of the intake manifold is poor at best and it looks like it was just a rebadged venom/golden eagle unit. I don't know what this makes compared to stock but again based on my experience I would almost think that it kind of hurts the power, or at least compared to a properly designed piece. A box with runners is not conducive to laminar flow.
Either way, the car makes good power and I'm sure it's a blast to drive.
Also the intake manifold I got was from Descendant Racing, is that a terrible manifold? Worse than Stock?
I don't know what the hp difference or spool up difference is between that manifold and stock but in my experience with intake manifolds normally a box plenum with short runners can harm air flow rather than help it.
However without before and after numbers I can't say for certain. I was merely trying to point out possible reasons as to why the spool was so late on the setup. I make 27lbs on a stock 4g63 engine (2.0 liter) by 4250 on the same turbo. While this might be apples to oranges its just to give you something to compare to.
Please don't think I'm knocking your setup. I'm just trying to help maybe squeeze some more from what you have
#202
Senior Member
OhioScions
SL Member
Thread Starter
Join Date: Oct 2006
Location: Columbus, OH
Posts: 139
No no, I am not taking that way! I was talking to them on how to fix it actually, I think it has to do with the Stock THrottle Body only being like 45MM. I saw in a magazine that AlphaWerks was supposed to come out with a 60MM TB by late this year. I sure hope its true.
#204
Originally Posted by scikotictc232
so how does a tc with 500 feel like ? stock tc throttle body is only a 45 ? damn 1st gen neons come with 50 stock for a 2.0
Originally Posted by B_Real45
Originally Posted by Nastos
wow on stock brakes and rotors?
#206
Senior Member
OhioScions
SL Member
Thread Starter
Join Date: Oct 2006
Location: Columbus, OH
Posts: 139
Originally Posted by scikotictc232
so how does a tc with 500 feel like ? stock tc throttle body is only a 45 ? damn 1st gen neons come with 50 stock for a 2.0
Originally Posted by jamie1tc
Sick! I always wanted 500hp......in a my scion.......how much time and money? I take it you did most of it yourself?
#207
It's funny.
I have built alot of high horsepower stuff in my time. Hondas, Mitsus, nissans, etc. I have come to the conclusion that it doesn't matter what kind of car you have. Horsepower made falls into a certain bracket. To make 500+ reliably, key workd here is reliable. it generally takes 30K.
Hope everything stands the test of time for you.
I have built alot of high horsepower stuff in my time. Hondas, Mitsus, nissans, etc. I have come to the conclusion that it doesn't matter what kind of car you have. Horsepower made falls into a certain bracket. To make 500+ reliably, key workd here is reliable. it generally takes 30K.
Hope everything stands the test of time for you.
#208
Senior Member
OhioScions
SL Member
Thread Starter
Join Date: Oct 2006
Location: Columbus, OH
Posts: 139
Well Don! I think I found the problem! Didn't take long for me to break the car:
Well after driving the car around this afternoon before I left to North East Ohio, the car was really acting up. Wasn't sure what was wrong however thought the clutch was giving me a few problems. Well I decided to call off the trip and investigate why my car was acting up again. Didn't take long after checking the Axles to see if something was broken.
It wasn't an Axle, it was the intercooler piping. Shaved all the way through:
And another major problem: The Fuel Pressure Regulator was flopping around like a ragdoll, making a horrible noise that I told them ABOUT! Nick(my buddy) and I could not figure out what it was.......till now
So whats the verdict? Think I will break 600HP with a fixed pipe? I think this has been causing my idling issue for a LOOONNNNGGGGG time
Bracket completely broken
Flopping in the Engine (broke the Gauge)
Well after driving the car around this afternoon before I left to North East Ohio, the car was really acting up. Wasn't sure what was wrong however thought the clutch was giving me a few problems. Well I decided to call off the trip and investigate why my car was acting up again. Didn't take long after checking the Axles to see if something was broken.
It wasn't an Axle, it was the intercooler piping. Shaved all the way through:
And another major problem: The Fuel Pressure Regulator was flopping around like a ragdoll, making a horrible noise that I told them ABOUT! Nick(my buddy) and I could not figure out what it was.......till now
So whats the verdict? Think I will break 600HP with a fixed pipe? I think this has been causing my idling issue for a LOOONNNNGGGGG time
Bracket completely broken
Flopping in the Engine (broke the Gauge)
#209
hey bro if you need help kicking someones ___ from that shop fly me over to ohio, Im down. haha that sux man. I hope you break into 600 that ____ would be sick. keep it up man. I am sure you have everyone on here supporting your efforts. And Dezoddon when you gonna build a high horsepower 2az-fe ?
#210
Senior Member
OhioScions
SL Member
Thread Starter
Join Date: Oct 2006
Location: Columbus, OH
Posts: 139
I'm not going to jail over a very childish mistake. However I already talked to them last night. They agreed to look at the pipe and possible fix it. However unless they are doing it free I am going to another shop in town. I tried to see if one of my buddies had a TIG welder but he doesn't.
#212
Senior Member
OhioScions
SL Member
Thread Starter
Join Date: Oct 2006
Location: Columbus, OH
Posts: 139
In that hole in the fender where the stock air box goes through. Over the Drivers WHeel and through the fender. I guess I will have to ziptie a silicone coupler to it.
#215
Senior Member
OhioScions
SL Member
Thread Starter
Join Date: Oct 2006
Location: Columbus, OH
Posts: 139
Originally Posted by scikotictc232
i see what your saying. when do you think youll have that done ? you plan on doing any drag racing ?
Originally Posted by Ace83
you got built axles right? if not, get some towing arrangements ready or a spare axle so you could drive it home lol
#217
Senior Member
OhioScions
SL Member
Thread Starter
Join Date: Oct 2006
Location: Columbus, OH
Posts: 139
HAHAHHAHA, this ____ never ends. I broke the clutch today! I am pulling the motor on Wednesday. Since I gotta drop a few things and remove A/C. Anyhow should be running again by next month. Sending the clutch off ASAP
#220
Originally Posted by scikotictc232
And Dezoddon when you gonna build a high horsepower 2az-fe ?
Originally Posted by OC3RULZ
In that hole in the fender where the stock air box goes through. Over the Drivers WHeel and through the fender. I guess I will have to ziptie a silicone coupler to it.