Joyride

So yeah i need to know if the Dezod S1 turbo kit will fit under my kaminari reverse cowl hood. Anyone have any experience with this?

06sciontcnda704

iTrader: (1)

whats this you geting a turbokit finally?

Joyride

lmao, an opportunity presented itself and i finally got an awesome paying job haha. A properly maintained dezod s1 for 1k with an entire kit. Just need to see if it will fit rofl

crush02342002

iTrader: (2)

id swear it does but i really cant be sure, there is someone roaming around here thats done it I think. ill look around

Joyride

thank you kind sir. Its just that damn waste gate that is positioned so awkwardly

crush02342002

iTrader: (2)

if it makes you feel better i found that it does fit with a turbonetics kit...ill post a link in a sec

Joyride

I dont even remember if the turbonetics had a retarded wastegate positioning..did it?

crush02342002

iTrader: (2)

https://www.scionlife.com/forums/sho...erse+cowl+hood

x_Batman_x

iTrader: (3)

the turbonetics kit's WG positioning is very similar to the S1's except that it sits even higher. I have seen turbonetics kits fit with Kami hood so I am certain it will fit with the S1

crush02342002

iTrader: (2)

it sticks up pretty freakin high, a buddy of mine has that kit and it punches a hole in his stock hood liner.

Joyride

I think the best bet will go to the guy im interested in buying from and put my hood on his car hah

crush02342002

iTrader: (2)

it fits

https://www.scionlife.com/forums/sho...dezod+kaminari

but read carefully

Joyride

damn thats retarded high..






Maybe it will fit haha.

Btw crush this is a question for you.
Dezod T3/T04 Spec'd Turbo (Precision turbo)
Dezod Stainless Steel TIG Welded Turbo Manifold
TiAL 38mm Wastegate w/ a .6 BAR Spring (8.7 PSI)
Dezod Aluminum mandrel bent charge piping w/ AEM Dry-Flow filtered intake
Dezod 2.5" Stainless Steel downpipe (catless)
HKS SSQV Blow Off Valve
550cc injectors
Dezod stainless steel braided oil feed lines
Dezod large bar & plate front mount intercooler
Plug-N-Play AEM FIC w/ Base Calibration (comes with harness, direct pNp)
Dezod Vacuum Block with some vacuum lines
Free Prosport Boost Gauge and Prosport Oil Pressure Gauge

Turbo has 10k on it and has been properly maintained, no problems for 1k. You Approve?

crush02342002

iTrader: (2)

no wideband?
not a fan of prosport at all but should be good for the time being, deff upgrade though. everything els sounds like a winner to me. check shaft play and check for oil in the charge pipes.

Joyride

Yeah the guy was going to check that for me tomorrow. And the electronics will be replaced in the time as well. Ill prob buy the kit, then save up for a new clutch, flywheel and install that before the kit goes on. So ill prob have new gauges by then.

crush02342002

iTrader: (2)

to tell if the turbo has too much shaft play grab the shaft and lift up while trying to turn it, if you hear it scratching like nails on a chalk board the turbo will need to be rebuilt but may be salvegable. if the turbo wheel wont spin at all when you lift up then the turbo is most likely trashed meaning it has a high likely hood of not being rebuildable at a decent price.

Joyride

Yeah before i actually buy it im bring my 3 mechanics specialized in turbos with me to inspect the actual turbo and manifold.

At least with this kit my car will be done. Then i can save for my motorcycle lmao. ____ing addictions.

crush02342002

iTrader: (2)

lol...wish ya the best of luck and happy boosting!!

Joyride

Thank you sir. Ill probably be trolling these forums now if i get it lmao. (Even though the lounge is dead and i have nothing to troll =( )

crush02342002

iTrader: (2)

yeah the lounge is kinda dead