tikbhoy

so i have the following

greddy ultimate
a/f harness ( to w/b )
map sensor
pnp harness ( made by dezod? have to check with kytc )

* just need to check make sure im doing things right.

found this 2 thread

https://www.scionlife.com/forums/vie...=greddy+jumper

https://www.scionlife.com/forums/vie...=greddy+jumper




post with regards to chips coming loose
http://mohdparts.com/emanage/emu_mis...hip/index.html

i only got the operations manual but not the installation manual. i did find that greddy has the installation files online and that i have to read.

Greddy Ultimate
http://www.greddy.com/img/PHP/products/pdf/806.pdf


===========

I just need help to make sure im doing things right, on the DIP switches and Jumper settings inside.


Thank you for any help

ROCKET77

The quote is correct . All you have to change is jp8 from 1-2 to 2-3 , with the dezod pnp harness . That's what i did and i been running for months without a problem . Good luck !

zer0

Yea change the jumpers, then install emanage. turn ignition to ON. Update firmware on Emanage. load the parameter settings for the 2azfe, then fire up your car.

paul_dezod

Word!!! All looks gravy with the above 2 posts.

Crippie

bump

tikbhoy

I can't load da pdf on my sk3 n I remember seeing a jumper for the option ports, I hav da a/f and map wit the kit.

???

tikbhoy

ttt

Crippie

hey guys... i just followed the instructions on the first few posts and my car started right up. its smokin a bit,... is that normal>?

anything else i should change in the fuel map?

zer0

Im me, might be able to send you a better map.

Crippie

lol.. sorry man... dont have aol or AIM. <---- lives under a rock

krdshrk

Bog - not spreadin around my map are you? :p

zer0

Negative, I have no use for your map... another Greddy owner in the area shared his street tune with me. I also borrowed his Ultimate to prove mine was a dud.

Which BTW, Tikhboy.. if your car doesnt start with jumpers and parameters set. Your emanage ultimate is a dud. Happened to me..

yamaha16bw

Dude youve had some bad luck getting that Greddy kit up and running. Is it all worked out now?

zer0

Greddy currently has my EMU. Should have it back later this week.
In the meantime, I will waste some $$$ and get black couplers tomorrow.

tikbhoy

i will try this weekend if i can get some free time from work.

i got it from kytc, so knock on wood that it works perfect.

equinox2355

I gotta find a good Emanage Ultimate tuner near me, I have it all ready with a PnP harness, but it needs a tune bad... I dont drive with it in, because I doubt its safe to drive it un-tuned... but I could be wrong...

Crippie

Anyone know where on the pic i would be able to place a water temp sensor for one of my gauges?

Also... looking to confirm that the gray wire on the o2 sensor is the correct one for a narrow band a/f meter? Im in the process of shopping for a AEM UEGO, but looking for a good price... and since i already bought the narrow band, figured id use it for now.

zer0

Water temp, get an adapter like this and put on the lower rad hose. Measure the ID of the stocker then buy one on ebay.
http://cgi.ebay.com/ebaymotors/ws/eB...m=270080264719

tikbhoy

i havent read the manual yet but can u have it hooked up but not tuned yet?

zer0

Yes, just remove the tune. And just have the parameters set for 2AZFE.