scion_andrew

iTrader: (2)

Finally started to install my kit tonight haha only installed One part but im excited!
treadstone mani
garett 57 trim turbo
turbonetics wastegate
greddy rs bov
greddy ic piping
ebay intercooler
dezod vac block
550cc injectors emanage blue
dezod pnp harness
an 3in dp back exhaust with a carbon ti!








Will keep updated as i finish it up!

dqlostsoulz

iTrader: (3)

oh lookie lookie mr. big shot with his turbo...haha..naw good for you man! You neeed to get a camera bro so you can capture the beauty.

scion_andrew

iTrader: (2)

Dq i have been wantin to have a turbo for years hah! i wanna camera but there over priced!

dqlostsoulz

iTrader: (3)

Well you are well on your way young grasshopper. Looking forward to seeing the progress..hopefully with better quality pics ..

crush02342002

iTrader: (2)

good luck and take your time doing the install....

scion_andrew

iTrader: (2)

^thanx, but i have a question my turbo intake tube is bigger that the turbo by a little bit would it be ok if i jus clamp it down to fit or should i get a smaller tube?

Chrisb319

iTrader: (1)

nice!

crush02342002

iTrader: (2)

you mean coupler? depending on how much bigger the coupler is it could cause issues. try it out and see what happens.

scion_andrew

iTrader: (2)

the coupler an the pipe , the pipe it self slides right over the turbo .

Prototype_xB

what kit is this?

rhythmnsmoke

Sounds like you need a reducer coupler (bigger on one end for the pipe, and tapers down on the other to fit the turbo).

my06tc

iTrader: (2)

where you get those eyelids at

scion_andrew

iTrader: (2)

OK this is how it looks its not much bigger but its deff bigger as u can see in the pic, how do i know which coupler to order?

Also wat is the wire im holdin in my hand i jus plug in the pnp haness correct? an dont use the wire im holding???


Thanks for the help this is my 1st turbo instal

crush02342002

iTrader: (2)

what travis said..

the wire i think your holding is the universal harness...not sure since iv never delt with the greddy brand engine management, looks like you would just go with the pnp harness.

crush02342002

iTrader: (2)

something like this....find out exactly the od of each and get the correct coupler

http://www.sfxperformance.com/parts/SPT8772.htm

http://www.streetsideauto.com/produc...NON&Reset=True

http://www.streetimports.com/products.asp?catid=179

cburglb34

hey that wire is the universal HARDWIRE harness, put it aside and save it incase the PNP for somereason goes bad..


as for ordering the right coupler...get a tape measure and measure the size of the intake pipe...prop is a 2.75 or 3inch

and then measure the turbo inlet its prob like 2.5

then go on ebay or something and get a 2.75in to 2.5 inch coupler or a 3-2.5

cburglb34

and btw couplers can strech .25 inchs so a 2.5 can fit a 2.75, or a 2.75 can fit a 3inch


takes some elbow grease but itll work incase u happen to order wrong size or just get lazy

tCjosh

iTrader: (8)

freakin andrew!!!! i thought you had this kit installed a long time ago! what kit is it???? i hate you and bobby now! both of you are tubo'd and im still n/a!! hopefully on income tax i can buy a kit then we'll all race eachother again! lol when are you coming down here? you and bobby should race and see who's faster now....

scion_andrew

iTrader: (2)

Just a kit i have put together!

scion_andrew

iTrader: (2)

hah it has been sittin in my room, bobby has a stage 0 i think il beat him easy!