A-snell

iTrader: (4)

DUDE!! your Lights ROCK!! I love mine.. now I just need to save the $$ to ship you me dash gauges and all the others little lighted stuff too.

Garage1217

iTrader: (5)

Right on! I knew you would dig them, everyone does after they get them installed!

Garage1217

iTrader: (5)

Hope you all had a great Thanksgiving! Hope all travels were safe!

Garage1217

iTrader: (5)

Christmas is coming BUMP! Cannot wait! get your orders in asap for a quick delivery!

Garage1217

iTrader: (5)

Happy Holidays! I hope everyone stays safe on the roads and may you all have an excellent Christmas!

Garage1217

iTrader: (5)

Weekend bump! Wow 2010 already?

Garage1217

iTrader: (5)

Been a very busy few weeks with the new products on the website! Do not forgot to check out the new flagship LED dome lights! They are wicked!
http://store.garage1217.com/new-flag...ut-wi3636.html

We also now stock a longer festoon for the xA as well!
http://store.garage1217.com/new-alum...519416839.html

And for those that have older clusters with twist style bulbs, we have our custom built led replacements that cast a very even light! Mr2 guys are going nuts for them! I bet the Lexus guys will catch on quick as well!
http://store.garage1217.com/custom-t...tput-bulb.html

Garage1217

iTrader: (5)

Monday BUMP!

Garage1217

iTrader: (5)

Friday BUMP! This week has gone by way to slow!

KyuubitC

my question is how do you accomplish a 2 tone effect with the stock gauge faces. do I have to use some screens of some sort? I want the numbers to light up white and the outter lines red. or am i stuck lighting up a single color?

Garage1217

iTrader: (5)

You use white leds to back the gauge faces and then use translucent vinyl to make the areas you want a certain color, that color.

KyuubitC

I suppose thats easy enough, just will need to do resistors and get some color pieces

Garage1217

iTrader: (5)

All of it is available in my webstore
http://store.garage1217.com/

PeArLwHiTe07tC

iTrader: (2)

out of curiosity, i just ordered a set of leds for the conversion. last night i took apart my hvac controls just to see what i was up against, and came across one issue. how do u swap out the leds for the lcd display? do u have to undo all the little solder pins holding the lcd connectors because there is a plastic bezel that the lcd sits on thats in the damn way of the led? any input would be appreciated.

SquallLHeart

i remove the LCD by desoldering all the pins.

Garage1217

iTrader: (5)

Correct, you need to de-solder all of the pins with a solder sucker and carefully remove the screen. If it is not done properly and if you pull on the screen at all with one of the leads attached it will crack and be useless. This is the #1 issue I see from diy customers. Just take your time and make sure each pin is free.

Garage1217

iTrader: (5)

Almost Friday bump!

Garage1217

iTrader: (5)

TGIF BUMP!!!! Man this weekend could not come soon enough!

cobaltbravo

whats the best way to remove the old IC off the HVAC board? desoldered the two contact legs but the body is pretty reistant in coming off the board. also, what weller iron would you recommend to a DIY'er for doing these swaps? the 15w iron from radioshack gets me by on clusters, but looking to upgrade. any suggestions welcomed.

Garage1217

iTrader: (5)

The only budget iron I will recommend is this unit. They are many times better than any irons you will find in the $200-$500 range, and I mean leaps and bounds better and I stand by that statement. Once you use one, you will know why I recommend it
http://www.circuitspecialists.com/prod.itml/icOid/9749

For a tip, use either of these for plcc work.
http://www.circuitspecialists.com/prod.itml/icOid/8401
http://www.circuitspecialists.com/prod.itml/icOid/8402

For de-soldering the IC, I set my iron to 350C and set the tip at the edge of the metal on the top of the ic. Let it sit for about 5-10 seconds until you see the flux start to boil on the sides of the ic, then lift hard using the tip of the iron and it will pop loose.