Removed Rear Wiper and Emblems (pic)
#6
yeah they have an inch and the next highest is 1-1/8 which is too big... so i put in the 1 incher and then with the inside hatch cover removed i just used pliers and meanuvered all the prongs on the plug to keep it in...
#7
looks good bro!...I did the same this past week, but at the same time I went ahead and painted my rear tails, and did the super soaker mod to the rear windshield nozzle. But Im suprised you broke the clips- i didnt break a single one. The trick is to loosen them all then finish removing them once they are all out of place. Buuuut too late to tell you that, oh and I lost one of mine if it makes u feel better?
#9
Originally Posted by Bossman
looks good bro!...I did the same this past week, but at the same time I went ahead and painted my rear tails, and did the super soaker mod to the rear windshield nozzle. But Im suprised you broke the clips- i didnt break a single one. The trick is to loosen them all then finish removing them once they are all out of place. Buuuut too late to tell you that, oh and I lost one of mine if it makes u feel better?
or do you take that whole little **** thing off?
#13
Originally Posted by implayaz9
is there a tutorial on how to remove the rear viper?
1. Remove the rear wiper. Flip up the cover at the base and I think it's a 10mm nut. Most people have found the wiper is tough to get off. If you have a gear puller, life will be easy. If you don't, it's going to take some pulling and maybe some oil to get it free. That's the hardest part.
2. Open the hatch and remove the rear panel. Use a small screwdriver to pry the plugs out but be careful not to destroy them because they have to go back in.
3. Unplug the motor.
4. Unbolt the motor. If I remember right it's 2 12mm bolts.
5. Slide wiper post out of the grommet.
6. Remove the rubber grommet from the hatch.
7. Plug the hole.
#14
Originally Posted by bobbyjay
do you just turn it so it sprays up?
or do you take that whole little **** thing off?
Hey so your in HB?....Gotta keep an eye out for your car now!
#15
shoo shoo, theres a scion meet in HB at the new bella terra sept 9th maybe we can cruise their, i got like 5 or 6 friends with xb's and were goin in a pack the more the marrier? merrier? i hate not knowing how to spell something, im going to dictionary.com after this, yeah anyways haha yeah for sure ill keep in touch and i got a 06.5 too i guess because mine has two spray holes by 06.5 do you mean like 2006.5?
#16
Looks Great!
Where did you get the plug, what size did you go with... Hope to do this to my TCM this week.
Originally Posted by chadfo
You can sand and paint the stainless plug so it doesn't stand out. I painted mine camo to match the car.
#18
Originally Posted by streetdemon13
when you debadge the xb are the badges held buy silcone or is there an actual hole behind them im gonna have to plug...and what would be the best way to debage it any way...heat gun
https://www.scionlife.com/forums/viewtopic.php?t=20747
#19
Originally Posted by 5C10N_DR1V3R
Here is a DIY from the tech section. It should anwser all of your questions.
https://www.scionlife.com/forums/viewtopic.php?t=20747
#20
Originally Posted by 5C10N_DR1V3R
Looks Great!
Where did you get the plug, what size did you go with... Hope to do this to my TCM this week.
Originally Posted by chadfo
You can sand and paint the stainless plug so it doesn't stand out. I painted mine camo to match the car.