Confirmed: Allan Phillips Racing ECU working on xB2
05-16-2010 | 05:51 AM
#27
05-17-2010 | 04:37 PM
#28
Thread Starter
Banned
Scionetics
KAD
SL Member
Joined: Oct 2005
Posts: 11,936
From: Western NY
05-18-2010 | 05:05 AM
#29
I had some trouble getting the Xtune software working but figured it out. After installing Xtune I kept getting an error msg about the work folder being missing. Then I installed one of APR's Taco base map calibrations, found your cal map on the flash drive and moved it to the APRcal folder. Works like a charm now in XP SP3 and Win 7.
Xtune looks a bit intimidating at first but I think I can manage it. I assume that the Mafadj table is for fine tuning the MAF (if necessary) after finding the correct MafID. Pull a little here, add there?
Anyway, thanks Paul. I'll probably call you tomorrow with questions.
05-18-2010 | 02:36 PM
#30
Thread Starter
Banned
Scionetics
KAD
SL Member
Joined: Oct 2005
Posts: 11,936
From: Western NY
Nice! The unit arrived today and wow! what a harness! You weren't kidding about it being a PITA to wire. It's long enough to place the APR behind the glove box too, thanks.
I had some trouble getting the Xtune software working but figured it out. After installing Xtune I kept getting an error msg about the work folder being missing. Then I installed one of APR's Taco base map calibrations, found your cal map on the flash drive and moved it to the APRcal folder. Works like a charm now in XP SP3 and Win 7.
Xtune looks a bit intimidating at first but I think I can manage it. I assume that the Mafadj table is for fine tuning the MAF (if necessary) after finding the correct MafID. Pull a little here, add there?
Anyway, thanks Paul. I'll probably call you tomorrow with questions.
I had some trouble getting the Xtune software working but figured it out. After installing Xtune I kept getting an error msg about the work folder being missing. Then I installed one of APR's Taco base map calibrations, found your cal map on the flash drive and moved it to the APRcal folder. Works like a charm now in XP SP3 and Win 7.
Xtune looks a bit intimidating at first but I think I can manage it. I assume that the Mafadj table is for fine tuning the MAF (if necessary) after finding the correct MafID. Pull a little here, add there?
Anyway, thanks Paul. I'll probably call you tomorrow with questions.
05-26-2010 | 07:37 AM
#34
On the positive side, the engine starts just like oem now. It no longer has to crank twice as long before starting like it did with the FIC. It also reads accurate rpm and TPS without any user calibration. It's not perfect yet but initial impressions are that it starts off much like a pro-tuned FIC or Ultimate and just gets better from there as you fine tune it.
More to come...
05-26-2010 | 03:47 PM
#35
Thread Starter
Banned
Scionetics
KAD
SL Member
Joined: Oct 2005
Posts: 11,936
From: Western NY
I am impressed. It took longer than anticipated to get the X1 installed due to other obligations and weather but today I finally completed the permanent installation. I'd been running it temporarily installed in the engine bay but couldn't do much with it like that. Even so, initial OBD2 logs showed LTFTs in the 0 to-6% range with STFTs ranging from 0 to 2%. Except for hot idle which is still a problem. Hot idle STFT still hits +20% as it did with the FIC and I'm not sure why. A vacuum leak or any post-MAF intake air leak would explain it but I haven't found any yet. Still looking.
On the positive side, the engine starts just like oem now. It no longer has to crank twice as long before starting like it did with the FIC. It also reads accurate rpm and TPS without any user calibration. It's not perfect yet but initial impressions are that it starts off much like a pro-tuned FIC or Ultimate and just gets better from there as you fine tune it.
More to come...
On the positive side, the engine starts just like oem now. It no longer has to crank twice as long before starting like it did with the FIC. It also reads accurate rpm and TPS without any user calibration. It's not perfect yet but initial impressions are that it starts off much like a pro-tuned FIC or Ultimate and just gets better from there as you fine tune it.
More to come...
05-30-2010 | 06:22 AM
#38
Thanks buddy, I need it...
I'm still trying to get the software working correctly. As of now I can't save changes or data log. The software gives an invalid path error msg on cal file saves and crashes when data logging. The X1 itself works great but I need to make a few tweaks and the SW isn't cooperating.
I'm still trying to get the software working correctly. As of now I can't save changes or data log. The software gives an invalid path error msg on cal file saves and crashes when data logging. The X1 itself works great but I need to make a few tweaks and the SW isn't cooperating.
Last edited by ScionFred; 05-31-2010 at 02:30 AM.
06-01-2010 | 04:11 PM
#39
Thread Starter
Banned
Scionetics
KAD
SL Member
Joined: Oct 2005
Posts: 11,936
From: Western NY
Thanks buddy, I need it...
I'm still trying to get the software working correctly. As of now I can't save changes or data log. The software gives an invalid path error msg on cal file saves and crashes when data logging. The X1 itself works great but I need to make a few tweaks and the SW isn't cooperating.
I'm still trying to get the software working correctly. As of now I can't save changes or data log. The software gives an invalid path error msg on cal file saves and crashes when data logging. The X1 itself works great but I need to make a few tweaks and the SW isn't cooperating.